Beyond FlipScreen Guía de instalación descargar pdf

RPSB 1800/1802 Installation Guide

Adjusting the Projected Image

After installing, connecting and powering up your RPSB components, you must perform a few

simple adjustments to ensure that the image from your computer is correctly projected onto

the SMART Board. To adjust the projected image, three procedures are necessary:

1. Ensure that computer and projector resolutions match at the software level.

2. Adjust the angle of the small front mirror.

3. Adjust the position of the projector itself.

NOTE

: The large rear mirror in every RPSB model never needs adjustment. The angle of this

mirror is entirely dictated by your choice of projector and is precisely set at our factory.

1. Matching Computer Resolution to Projector Resolution

It is very important that computer and projector resolutions match. If they don't match, the on-

screen image will not properly fill the SMART Board screen.

You must first ensure that the projector is set to its optimal image resolution. Refer to your

projector’s manual for the true resolution of your projector, and reset it if necessary. While

these instructions may indicate that resolutions other than the optimal one are permitted, you

should not set the resolution to any of these other settings. For example, if the projector’s true

resolution is 800 x 600, but it's also capable of displaying at 640 x 480, set both the computer

and the projector to the true resolution



800 x 600.

IMPORTANT

: If the resolution of the projector is set to anything other than the true

resolution, or if the computer and projector resolution do not match, you may be unable to

see all of the image on the SMART Board, or the image that appears may be too small to

properly fill the SMART Board, even with further adjustments.

To set your Windows 95 computer resolution to match the projector resolution:

1. Click the Windows 95

Start

button and then point to

Settings

NOTE

: You may need to perform the following procedure via your computer monitor,

as resolution differences can distort the image on the Board to the point where

visibility is impaired.

2. Point to the

Control Panel

folder and release the mouse button.

The

Control Panel

directory of folders will appear.

3. Double-click on

Display

The

Display Properties

dialog box will appear.

4. Click on the

Settings

tab.

5. In

Desktop area

, click and drag the sliding bar to adjust the pixel setting to match the

resolution of your projector.

6. Click the Apply and OK buttons.

7. Restart your computer, if required.

1 2 3 4 5 6 ... 21 22

Indice de contenidos

Pagina 1 - Adjusting the Projected Image

RPSB 1800/1802 Installation Guide35Adjusting the Projected ImageAfter installing, connecting and powering up your RPSB components, you must perform a

Pagina 2 - Reflection

RPSB 1800/1802 Installation Guide44Appendix A: Maintenance and TransportationCleaning Cabinet Components and MirrorsMirrors and cabinet components sho

Pagina 3 - 3. Adjusting the Projector

RPSB 1800/1802 Installation Guide45• Remove the two mirror lock screws, and rotate the large rear mirror upwards untilit stops (lifting top baffle sli

Pagina 4

RPSB 1800/1802 Installation Guide46Removing and Reinstalling the RPSB 1800/1802 ScreenYou may need to remove and then reinstall the RPSB 1800/1802 scr

Pagina 5 - Completing the Installation

RPSB 1800/1802 Installation Guide47 3. Disconnect the MOD4 cable at the bottom center of the screen.4. With the aid of another person, remove th

Pagina 6 - Macintosh Installation

RPSB 1800/1802 Installation Guide48Appendix B: A Quick Guide to RPSB UseThese steps can be followed once the RPSB has been set up and the SMART BoardS

Pagina 7 - To orient the SMART Board:

RPSB 1800/1802 Installation Guide49 If you are unable minimize the SMART Board window by touching on thescreen, you must put the software in projected

Pagina 8

RPSB 1800/1802 Installation Guide50 NOTE: You do not need to shut down the SMART Board driver program.2. Exit the operating system.3. Use the projec

Pagina 9 - Customer Support

RPSB 1800/1802 Installation Guide51Appendix C: Integrating a Video Camera andShelfTo integrate a video camera and shelf, you must first gain access to

Pagina 10 - Transporting the RPSB System

RPSB 1800/1802 Installation Guide52GlossaryAware: See SMART Aware.Baffle: An obstruction that prevents the flow of light, noise, etc. Baffles are plac

Pagina 11 - Lower baffle lock screws

RPSB 1800/1802 Installation Guide53Serial port adaptor, 9-pin: A device that accepts an RJ11-6 connector at one end andconnects to a DB-9 serial port

Pagina 12

RPSB 1800/1802 Installation Guide36To set your Windows 3.1 or 3.11 computer resolution to match the projectorresolution:1. Go to the Windows 3.1 Prog

Pagina 13 - (center and both sides)

RPSB Installation Guide54IndexAAdjusting the Projected Image, 29Adjusting the Projector, 31BBolting projector to the platform, 7CCabinet Tools, Cables

Pagina 14 - Starting up the Board

RPSB Installation Guide55SSelecting a COM Port for the SMART Board,36Setting Up the Keyboard, 8Setting Up the RPSB 1800/1802 Cabinet, 2Sliding project

Pagina 15 - Starting up SMART Notebook

Technologies Inc.Suite 600, 1177 - 11th Avenue SW, Calgary, AB CANADA T2R 1K9Support: 1.888.42.SMARTTel. 403.228.5940 Fax 403.245.0366E-mail: suppo

Pagina 16

RPSB 1800/1802 Installation Guide37 LoosenThumbscrewSMART BoardImageSm all MirrorSide ViewSm all Mirror(access from front doors)Move Image Up or Down3

Pagina 17 - Cut-Away View of Cabinet

RPSB 1800/1802 Installation Guide38Image Side-to-Side AdjustmentTighten the screws that secure the top of the platform when the correct position is ac

Pagina 18 - Glossary

RPSB 1800/1802 Installation Guide39Completing the InstallationTo complete the installation of your RPSB 1800 or 1802, you must replace the rear access

Pagina 19

RPSB 1800/1802 Installation Guide40Windows 95/98 and Windows NT 4.0 Installation1. Close all applications.2. Insert the SMART Board Software disk into

Pagina 20 - RPSB Installation Guide

RPSB 1800/1802 Installation Guide414. If you know the COM port that is connected to your SMART Board, select it from the listof ports provided.orIf yo

Pagina 21

RPSB 1800/1802 Installation Guide42A large gray rectangular image will almost entirely fill the SMART Board screen. Thisscreen will contain the number

Pagina 22 - Support: 1.888.42.SMART

RPSB 1800/1802 Installation Guide43Customer SupportContacting SMART Technical SupportAll SMART software includes one year of free telephone, fax, and

Comentarios a estos manuales

Sin comentarios

Beyond FlipScreen Guía de instalación

Busca en linea o descarga Guía de instalación para Proyectores de datos Beyond FlipScreen. Beyond FlipScreen Installation guide Manual de usuario

Indice de contenidos

Comentarios a estos manuales